This is the Honey Bee CP2 RC Helicopter sold by Nitrotek and comes with a 6 channel design. The Honey Bee rc helicopter should not be take this to be in the same model league as other rc helicopters on the market. This is an advanced model heli which comes with wooden blades and the ability to fly upside down due to more stability in flight. Even more advanced stunts can be flown either outdoors or in. The helicopter comes with a high capacity Li-Polymer battery which gives much longer flight times and safety precausions which are automatic and give fail safe’s.

Inside the box you will find the 6 channel radio controller which has the trottle on the left.

Specs

Main rotor diameter: 530mm
Weight: 305g
Length: 520mm
Power system: 370 motor
KIT or RTF: RTF
Control mode: CCPM system
Main blade material: wooden
Transmitter: 6CH CCPM system
Servo: 8g,1.3kg/CM,0.13s/60
Battery: 11.1V 1800mAh Li-Polymer with Li-Polymer UK charger
Mix controller: “4 IN 1″ controller(W/gyro,mixer,ESC, receiver)
Flying radius: ~400m
Flight time: ~25 minutes

More Info At Nitrotek 

The -Hobby Micro X rc helicopter is one of the most sought after rc helicopters so now available from Nitrotek. This is one fantastic fun helicopter, and ideal for any gadget or techie lover. Not to be confused with lower spec and cheaper 2channel and 3 channel rc helicopters you may have seen elsewhere for sale, this is one fab engineering marvel and comes with a full 4 channel long range radio control reciever. As you may or may not know, 2 channel rc helicopters are only able to go up and down or roate and cannot go far before going out of range. This allows you to go all sorts of 3D controls such as a left, right, bank left, bank right, move forwards, backward and up and down. Also, it has the ability to travel a couple of hundred meters in distance before it goes out of range, just like its full scale cousins. What is amazing is this rc helicopter is just the size of the palm of your hand. Driven by a rechargeable high capacity battery, which gives 7-10 minutes flying time. A charger is included with a UK plug.

Great high quality and packed in a smart gift box. The design uses counter rotating blades so easy to fly. Great fun for all the family and friends, so an ideal present to yourself or someone else.

1) Main Rotor Diameter (Upper): 175 mm
2) Main Rotor Diameter (Lower): 175 mm
3) Overall Length: 175 mm
4) Drive System: 2×1215 strong motors
5) Battery: 3.7V 400mAh Li-PO battery
6) All-up Weight: 57g (Battery included)
7) Transmitter: 4 Ch
Gyro: Built-in
9) Receiver: RX-412
10) Servo weight: 3.5g
11) Servo speed: 0.11sec/60°(4.8V)

More Info At Nitrotek

This Apache rc helicopter is easy to fly and looks amazing. This model comes with twin blades as do other models on the market but none look as good as this rc helicopter. Anyone can fly a twin blade rc helicopter so ideal for people with no experience, beginners and at the end of the day, just for fun. No more need for hours of practise, just start it up and away you go.

Please do not confuse this with toy helicopters though as this has fully functional 3D controls. You will find on the market, a similar two channel apache rc helicopter but does not let you have as much control over the machine as this one. This is better as it contains 4 channels so allows you to move it up, down, left, right, bank left and right as well as forwards and backwards.

All you need to get going are 8 AA batteries, it comes with everything else.

SPECIFICATIONS:
Rotor Diameter: 260MM
Length : 300MM
Weight: 80g
Flight time: 8 - 12 minutes
Transmitter: FM 4 channel
Motor: 2 x strong magentic brushed
Battery: Lithium Polymer 7.4V 350mAH

Click For More Info & Video To Watch

This 6 channel RC Helicopter is one of the newest single blade helicopters for acrobatics on the market and the highest quality helicopter from ESky. Included in the design are several performance enhacements such as the brushless motor system. This means the rc helicopter can out perform any other rc heli’s on the market.

Included with the heli

6 Channel Transmitter
25A Speed Controller
8g Servo
11.1v-1000mah HI-MH Battery
Li-polymet charger
Switching Adapter
6CH Reciever
Esky Gyro
450 Brushless Motor

As this Esky RC Helicopter includes a brushless motor, it means it has several ad compared with standard DC Motors. This includes, higher efficiency and reliability, longer lifetime (as there is no brush erosion) reduced noise. These combinations mean this rc helicopter is incredibly powerful but still able to complete very agile moves, as a heavy motor is not required.

There are many features included with this Belt-CP rc helicopter such as a belt driven tail motor, carbon fibre tail stand, alloy tail boom, and a top of the range gyro. This rc helicopter has everything you will need for a fantastic flying experience.

Specs:

(1).Length:650mm
(2).Height:230mm
(3).Main Blade diameter:680mm
(4).Tail Blades diameter :130mm
(5).Motor gear:10T
(6).Main driven gear:140T
(7).Tail driven gear:110T
(8).Driven gear rate:10:140/110:22
(9).weight:About 670g(Including 1800mAh,11.1V li-poly Battery)

Features:

(1).CCPM System
(2).Auto-rotation Stystem
(3).Tail rotor Belt Drive System
(4).High Inertial Main Blade
(5).High Rigidity Iron Main Shaft (6).Shock Proof Iron Landing Skids
(7).Full Ball Bearing & Metal Ball End
(8).High rigidity alloy tail boom

The Apache Twin Blade RC Helicopter is a amazing looking helicopter and easy to fly. With many twin blade rc helicopters on the market, they are all well designed but none look as great as this apache helicopter. With a twin blade rc helicopter, anyone can fly then with just a little practise and an ideal way to start a hobby with rc helicopters. With this great apache, you can have so much fun and thrills without having to practise for hours.

This helicopter is not to be confused with toy helicopters as this great machine has full 3D control. You will find there are very similar two channel versions on the UK market but have a limited amount on control but this four channel version is much better as you can go up, down, rotate left and right, bank left and right and go forward and back.

This apache rc helicopter comes with everything you need to get going apart from 8 x AA batteries for the rc controller.

SPECIFICATIONS & CONTENTS
Factory Assembled Helicopter
4Ch 35mhz Transmitter
UK AC Li-Po balanced charger
Li-Po 7.4V 350mAH
Spare Main Rotor Set
Instruction Manual
Rotor Diameter: 260MM
Length : 300MM
Weight: 80g
Flight time: 8 - 12 minutes
Transmitter: FM 4 channel
Motor: 2 x strong magentic brushed
Battery: Lithium Polymer 7.4V 350mAH

your rc helicopter on a table and look at the tip end of the main blades, the chordline of the blade can be tilted through a range of angles by the servos.

In this sense, the rotor disk of a heli is a bit like a variable-pitch prop on an airplane. If your helicopter is hovering in the air, and you want to make it climb straight

up in the air, you just increase the pitch of the main blades and turn up the throttle which means the helicopter can overcome the drag which increases and the blades

keep turning at the same rotation speed before the throttle was increased and the helicopter will rise

Overall the more you increase the pitch of the blades, the more the lift given to the rc helicopter. At high throttle the engine puts out more power, but there is a corresponding increase in the load on the engine due to increased main rotor blade pitch, and so the engine stays at the same RPM’s.) The general increase in pitch means that the helicopter will climb and is called collective control.

On a 4 channel rc helicopter, the pitch angle of the blades is fixed in places but as we said above, the 6 channel helicopters blades can be changed in pitch.

When calibrating rc helicopters, the controller needs to be set properly otherwise it will not calibrate properly so the following settings need to be
set on the controller

1. the left stick needs to be all the way down
2. the left vertical trim needs to be all the way down
3. The rev switches, both the bottom front right on your controlled need to be down put to DOWN, UP, DOWN, UP in that order starting from the left and then the right
4. If you rc helicopter is a 6 inch model then the idle switch which is found on the top left of the controller is set to the off position

Once these settings have been put in place, then turn on the controller and then you should connect the battery to the rc helicopter. You should find a red light on the
Receiver will flash a couple of times before turning green

If you complete all these settings and the calibration is still not set, then complete the following checks

1. The rc helicopter battery is fully charged
2. The same for the controller batteries
3. The frequency plug is inserted into the receiver properly
4. The same for the controller
5. Both the frequency and receiver number matches both
6. All the buttons on the first section above are correct and not just set half way. You can check this by turning them in the opposite direction and then back again
7. The controllers Ariel has been fully extended

If after all these checks it still does not work, contact the supplier

One of the most popular nitro rc cars is the HBX VRX-2 Nitro Rally Cross Buggy

Due to a huge demand, this has been out of stock for ages but will now be back soon. The VRX-2 is a fantastic high quality 1/8th scale rally cross nitro buggy and very fast with great addons and features. Go to many competitors and this car will set your wallet back much more, but as this is purchased direct from the manufacturer it can be purchased from us at a much lower price.

This is definatly not a entry level nitro car or anything like a 1/th Petrol RC Car but for Nitro Cars hobbyists. It comes with 3 shoe aluminium clutch, front CVD Shafts and tough aluminium parts throughout the chasis.

Due to it being a racing nitro car, it can be adjusted to suit different tracks and driving configurations.There is a video on the main site of this car in action and well worth checking out. See it here.

FEATURES:
1/8 Scale
Front Pivot Ball Suspension
Captured Arm Mounts
Front Universal Drive Shafts
Sealed Bevel Gear Diffs
Big Bore Racing Shocks
Complete Ball Bearings
Powerful .21 Pull Start Engine
44 Tooth Steel Spur Gear
Low CG Radio Tray
Fully Adjustable Suspension
3 Shoe Aluminium Clutch
150cc Fuel Tank w/ Filter
High Torque Steering Servo
Spiral Cut Steel Conical Gears
Heavy Duty Suspension Arms
27MHZ CE approved Radio system with changeable crystals.

The Conquistador is one mean Monster Truck

Run it towards any terrain and it will take it on with ease be it grass mud or sand, this monster truck is a powerful vehicle.

It comes with extra strong alloy shocks, a very big engine and strong chassis. The battery compartment is sealed to stop dirt and water getting in as this rc car can cause quiet a stir to the ground undeath its monster truck wheels.

There are two great videos to watch here, or click on the truck for more information, price and checkout.

This fantastic nitro buggy comes with a strong chasis, shaft driven 4WD system and sealed compartments so that dirt and water cannot get in. A very robust car and great fun even for those just watching this speedy guy. For those of you who are after a higher spec, there is also the Condor Pro. See the link to the videos and more details page.

Below is an image showing the different designs/colours you can buy this Condor in.